What are the commonly used installation methods of

2022-07-22
  • Detail

Many families prefer to install wood flooring, and the saying that has been widely spread in the flooring industry: "three floors, seven installation", shows the importance of wood flooring installation. There are four common installation methods of wood flooring, and each laying method can be selected according to people, ground and functional needs. Now let's have a detailed understanding of the relevant knowledge of wood floor installation methods

many families prefer to install wooden floors, and there has been a popular saying in the flooring industry: “ Three floors, seven installation ”, We can see the importance of wood floor installation. There are four common installation methods of wood flooring, and each laying method can be selected according to people, ground and functional needs. Now let's have a detailed understanding of the relevant knowledge of wood floor installation methods

I. installation method of wood floor &mdash& mdash; Keel laying try to

lay the keel first, and pop up the keel laying position according to the laying direction and length of the floor. Each floor shall be placed on at least 3 keels, with a general spacing of no more than 350 mm. Then fix the wooden keel. When the ground height difference is too large, level it with a skid. First fix the skid on the concrete base with shooting nails, and then fix the wooden keel on the skid with iron nails. If there are water pipes or floor heating facilities under the ground, do not drill holes. You can use new keels such as plastic steel and aluminum alloy keels, or use adhesives to make short wooden keels

the floor surface is generally laid in a staggered manner. After leaving a gap of 8-10 mm from one side of the wall, lay the first row of wooden floors. Outside the convex corners of the floor, fix the floor on the wooden keel with threaded nails and iron nails, and then fasten them block by block. All parts of each wooden floor that contact the wooden keel must be nailed with air gun nails, threaded nails or ordinary nails, and the length of the nails shall not be less than 25 mm

scope of application: Generally speaking, this installation method is mostly used for solid wood flooring and solid wood composite flooring

II. Installation method of wooden floor &mdash& mdash; Suspension paving method

the direction of the paved wooden floor is usually consistent with the direction of the room. It is paved row by row from left to right or from right to left. The groove is towards the wall. A wooden wedge is placed between the floor and the wall, leaving enough expansion joints. In dry areas, the floor is wet, and the expansion joint should be kept small; Expansion joints should be left large in wet areas because the floor is dry. During the trial paving, the height difference and gap of the plate surface should be observed and adjusted at any time. The glue can be applied and installed only after the inspection is qualified. Generally, the rows paved on the edge can be fixed with anhydrous environmental protection glue, and the other middle parts are completely engaged by tenon and groove, without glue. The last row of floors shall be cut and glued by measuring its width, and shall be tightened with hooks or screw tops

scope of application: generally used for tongue and groove floor and double tongue and groove floor

III. installation method of wooden floor &mdash& mdash; Plywood laying method

plywood keel laying method is to lay the keel first, then lay the wool floor on the top, fix the wool floor and the keel, and then lay the floor on the wool floor, which not only strengthens the moisture-proof ability, but also makes the foot feel more comfortable and soft. However, the layer height with more losses is also more expensive than other methods

the laying method is that the rough floor is laid on the keel, and there should be a gap between each row. Use iron nails or threaded nails to fix and level the rough floor and the keel. The rough floor can be laid into an oblique angle of 30 degrees or 45 degrees to reduce stress. Lay the laminate on the rough floor and try to lay it according to the suspended paving method

scope of application: it can be used for a variety of flooring, such as solid wood flooring, solid wood composite flooring, reinforced composite flooring and cork flooring

IV. installation method of wood floor &mdash& mdash; Paste paving method

is used for laying solid wood and cork floors with a length of less than 30 cm. Some small teak floors and parquet floors must be laid by direct pasting method. If the cement floor is paved directly, it must be leveled with cement. Compared with the keel leveling, it will not affect the floor height of the house too much, but the cement leveling requires a lot of cement and sand, and the cost will be higher. If cork floor is used, it is suggested to make cement mortar self leveling on the original foundation

scope of application: parquet floor, cork floor, and composite wood floor

summary: I'll introduce several common installation methods of wood floors here. Different installation methods are also different for different floors, so you should know which floor you use before decoration, which is more convenient for reservation and paving

北京肾病医院

北京男科医院

济南妇产医院

Copyright © 2011 JIN SHI